Media Library / Images

ELAFLEX Hamburg

ELAFLEX stock

Storz Safety Coupling SHK

upon uncoupling, the safety dust plug first falls into holding claws, relasing an eventual pressure within the system. Only then the dust cap can be fully taken off. - increased protection for the operating personnel. Easy to use, no additional pressure release necessary, slim design, does not build up, no freezing up in the dome section.

ZVA Slimline 2 for aircraft refuelling

black plastic cover (scuffguard), Sight Glass, dust cap and ground cable assembly

ZVG 2 DISH nozzle for L.P. Gas / Autogas, LPG 16 hose assembly, ARK 19 Safety Break

ELAFLEX refuelling equipment:

Quality is in the detail.

Large reel, HD hose assembly, ZH 50 nozzle

Hose assembly for L.P. Gas

LPG 50, DGC-M 50

DAC-M 65, DAC-V 65

MannTek Dry Aviation Couplings

TGN 4" Al tank truck flange with threaded nipple, VK 100 Ms male TW coupler, MB 100 Al dust cap, chain

VX 50-2" SS

Male hose coupling 2" BSP of stainless steel with Spannfix clamp

MannTek DGC DryGasCouplings for L.P. Gas

DGC-M 50 F, DGC-M 80-3", DGC-M 50-2", LPG hose

SVC 50-2"

Male hose coupling of steel with Spannloc clamps

Oasis CV Heavy Duty Check Valves for CNG

Road tanker hose reel, made by Elaflex Italia

with LPG hose assembly

Slimline 21 red

Quality petrol pump hose for gasoline and diesel fuels. Also suitable for fuels with ethanol content up to E 85 and Biodiesel up to B 30 (BIO Type up to B 100). Meets weights and measures regulations, see overleaf. Cold flexible down to - 30° C / - 22° F (LT-type down to - 40° C / - 40° F). Corresponds to EN 1360 and EN 13483.

DDC-M 50-2" SS

MannTek Dry Disconnect Coupling, DN 50, stainless steel

ELAFLEX Hamburg

ERV marking after test

DAC-M 65

MannTek Dry Aviation Coupling

ELAFLEX Hamburg

Assembling ERV large DN

Oasis NC 203 P30_P36 Nozzle Couplers

Polypal Clean hose assembly

Pharmaceutical production

Storz coupling on road tanker

Hose assembly with Spannfix clamp and stainless steel threaded connection

SG 1" 1x0 Al

Sight Glass with propeller, to EN 13617-1, DN 25, for installation between petrol station nozzle and hose assembly, or mounting on the dispenser. For the visual control of bubble-free dispensing and fuel colour (e. g. for premium fuels). Suitable for all standardised gasoline and diesel fuels according EN 589 + EN 590, including ethanol or biodiesel content, also Avgas and Jet-A1.

IBC loading

MannTek DDC-M 50, FWS 50 PTFE

ERV-R 200x175.16 ZS 4

Red Band Rubber Expansion Joint, special length 175 mm, with "ZS" limiter (tie rods with outer limitation in rubber bushings)

HD 10 C sensing hose

Use as sensing hose for aircraft dispensers (hydrant dispensers)

Vehicle refuelling with LPG (L.P. Gas, Autogas)

GasGuard GG30 BAYO nozzle with Bayonet connector and optional splashguard, LPG 16 hose assembly, ARK 19 Safety Break

ELAPHARM Type EPH-OHM G

electrically conductive 'OHM/T', with light grey cover, to EN 16820, Type A. FDA conform, homogeneous elastomer hose construction with smooth, black PTFE liner.

Hose assemblies

for petroleum based products, chemicals, foodstuff and pharmaceuticals, LPG

LNG Refuelling

Vent Coupling 'VC-LNG'